If you’re facing coverage problems with your wifi then wavlink wifi extender is the answer. Many Daily activities rely solely on internet. And as we know Wifi is the next best thing after the ethernet. Having a wifi with proper range and coverage is a must, if you want your work to go smoothly. You may be streaming online, having a gaming session, using it for work related project or may be just surfing on the net, all of can be enjoyed only by an uninterrupted wifi. If you have dead zones in your work space/ house then you just need an extender.
The extender basically catches your router’s signal and pushes it further, so the places that had weak or no signal now get better coverage. It’s not complicated, but a lot of people think setup is some kind of technical task. The truth is the Wavlink setup process is fairly simple if you know the steps.
Why Use a Wavlink WiFi Extender
The main reason is coverage. You don’t buy an extender because your internet speed is bad from your ISP. You buy it because your speed is fine near the router but terrible in other rooms. The extender repeats the signal, giving you stable coverage in bedrooms, basements, garages, or even upstairs where the signal usually dies.
Another reason is flexibility. Not everyone can place their router in the middle of the house. Sometimes it’s stuck near the entrance or one side of the house because that’s where the provider’s connection is. In such cases, an extender fills the gap without moving the router or running extra cables.
Unboxing and Getting Ready
When you get a Wavlink WiFi Extender, the package usually has the extender unit, a quick guide, and sometimes an ethernet cable. Plug the extender into a wall outlet close to your router for the initial setup. Don’t rush to put it in the farthest corner yet. First, you need it close enough so it can grab a strong signal during setup.
Check the indicator lights. Most models have LED lights that tell you the power is on and if the connection is working. Make sure your router is also on and broadcasting WiFi before starting.
Wavlink Setup Process (Basic)
Here’s the straightforward way. Plug in the extender. On your phone or laptop, scan for WiFi networks. You’ll see the Wavlink network name show up, something like “Wavlink-Ext.” Connect to it.
Once connected, open a browser and type in the default web address for the extender. It’s usually printed on the back of the unit or in the manual. A login page shows up. Use the default username and password (also printed in the manual).
After login, the extender setup page loads. You’ll see a list of WiFi networks around you. Pick your main router’s WiFi name, enter your router password, and confirm. The extender links to your router and creates a boosted signal. The extended network may have a slightly different name, sometimes with “_EXT” at the end, depending on the model.
Placement of the Extender
This is important. If you place the extender too far from the router, it won’t get enough signal to extend. If you put it too close, it won’t extend coverage to the weak areas. The best spot is about halfway between the router and the dead zone. You want the extender to still get a good signal but be close enough to cover the weak area.
Watch the LED lights on the extender. Many Wavlink models have a signal strength light that tells you if the placement is good. Green or solid blue means strong, amber or blinking means weak. Adjust until you find the sweet spot.
Using Ethernet for Stable Setup
Some people prefer to connect the extender using an ethernet cable. If you can run a cable from your router to the extender, you get an even more stable connection. The extender then works more like an access point. In that case, the extender broadcasts WiFi using the cable feed instead of repeating the wireless signal.
This is helpful if your walls are too thick or if wireless performance is unstable in your house. It takes away some flexibility but gives better performance in tricky setups.
Common Problems and Fixes
- Extender not showing in WiFi list- The extender can be reset by pressing on the tiny reset button for 10 seconds using a pin. Try again to connect.
- Incorrect password- Ensure that you are entering the password of your main WiFi and not that of your extender.
- No internet after connection- Almost certainly, the extender is connected to the router but not to the internet. Set it again and check the router settings.
- Signal is still weak- Set the extender near the router and slowly move it away.
- Interference- Make away from microwaves, cordless phones, so they cannot penetrate thick concrete walls.
Performance Expectations
A WiFi extender does not increase the speed of your internet plan. Also, the speed of your current internet plan can drop, but not much. This happens because the extender repeats the signal and the slight interference reduces the speed. But what you lose in speed you gain in stability and the coverage.
A wavlink wifi extender gives more than enough stability so that the user can accesses the net without interruption.
Advanced Settings
Many models allow the extension of both types of networks, i.e. 2.4 GHz & 5GHz. This feature can be accessed from the advanced setting of the admin panel. For any other kind of tweaks, you can check the different tabs given on the admin page. Features like setting a new password changing the name of the network, all can be done with ease. For extra security you can even the SSID (network name).
Wavlink setup page shows the new updates of firmware, whenever they are available. Updating the firmware not only enhances security but it fixes many bugs and improves performance as well.
Final Thoughts
You must have had a pretty good idea on how to configure a wavlink wifi extender. You just have to plug it in the power outlet and connect to its setup page. With a correctly configured wavlink setup your extender will boost up the range. And you can make the most of your house/work internet.
